Were you interested in additional info concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the job can move immediately; if you need to open a wall surface to remove the old bathtub and also position the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the work and fit trying it. Rather than working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one before you start. Chances are you may require a specialist plumber to make tube connections.
This write-up will certainly help you set up a brand-new bathtub in your restroom if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your devices and also material list should comprise the following:
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is detach the water system. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the water supply and also check all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub as well as likewise check the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has been made use of a minimum of when as this will certainly settle it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Protect the faucet in place with the supplier provided backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind ought to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, triggering the water to pass through the wall surface between the bath and the tiling, resulting in issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to permit the motion experienced when the tub remains in usage. The sealant can break rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were introduced to that article on Installing A Bathtub from a good friend on our other site. For those who liked our page kindly be sure to share it. Thank you for going through it.
Give Me A Quote!